It has a build in 3,000mAh battery, a screen that you can change the layout of and adjustable airflow. Woohoo it has airflow adjustment! And not just that! In the kit you get two airflow rings which you screw onto the base of the pod to fasten the coil. One airflow ring has 6 rather large openings for RDL vaping and one of them has just this one tiny hole which is meant fir MTL. This is so far the best pod-mod airflow wise, because both loose DTL and VERY tight MTL are possible. Love this airflow for MTL and it just fits the Z-Coil line perfectly, even with the outer airflow wide-open and the MTL ring attached it is already tight. Also, with the RDL ring you can get a tight MTL draw with the airflow closed. Airflow sounds smooth for the most part, just only with the DTL-ring it whistles when closing it down further than half.

The panel squeeze button is actually over the screen, on the front of the mod, which makes the front of the Sensis looks super clean and tidy. The button is easy to press irregardless of how you are holding the mod. I haven’t experienced any leaking with this pod at all. Using The Innokin Sensis Kit How To Change the Innokin Sensis Coils When it comes selecting an e-liquid, we recommend either a 50/50 or high PG e-liquid with the 0.65 Ohm Sceptre coil. The 0.25 Ohm Sceptre S coils will produce a larger amount of vapour for RDTL vaping and work best with either 60% VG or some 70% VG e-liquids. Refilling is very simple thanks to the bottom fill seal and the tank section will hold up to 2ml of e-liquid, while the seal system stops leaks from occurring. Tip: all the mods features (F0, Coil+, Refresh) worth with an appropriate tank connected with the 510 connector. Does the Innokin Sensis Leak? The only con for the battery part of the kit is that the connection between it and the pod is not as strong as it could have been. Innokin either needs to use stronger magnets, or they need a snap-in connection. Innokin Sensis Battery and ChargingI actually quite like this coil at 20W MTL with the airflow fully open, it proves a nice smooth drag with ample flavour. Generally the Sensis EZ ends up being such a good all-rounder for lower powered vaping but without sacrificing flavour and warmth, naturally vapour production is lower but for me that’s a huge pro for indoor vaping and vaping in public. The other benefit is the 3000mAh battery life which is excellent and would last me a full day and evening with the 0.65ohm coil. The Innokin Sensis is a highly innovative creation that is sure to catch a lot of heads. It produces quality clouds and vapor thanks to its advanced features, and its coils and airflow can accommodate a wide range of vaping styles. The 510 adapter is another excellent inclusion because it gives the user the ability to swap out tanks. The 0.3ohm coil is from my knowledge newly released with this device. It is a mesh coil intended for RDL. It provides a dense flavorful vape with medium vaper production. I really like this coil. One thing I noticed with this coil though is that when firing you get a very soft buzzing sound in the beginning. Also It is rated between 30-40W, but I have a feeling 40W is just a bit too much for this coil, because when chain vaping I tend to get dry hits from time to time, I like it most on 35W.

Now Innokin aren’t new to pod systems, but this is the first time Innokin has slapped the ‘Kroma’ name on a pod kit and added a ‘Z’ on the end for good measure! For me simply the best pod-mod if its about MTL. Z-coils are as always reliable, and the airflow can be set to very tight which for me is one of the most important things for an MTL vape. Along with the S-Coil options, the Sensis EZ is such a good all-rounder for those users that prefer a lower powered vape, and the Sensis excels in MTL andRDL but is more than capable of a decent DL vape at 35watts. and that’s very true, for example 25Hz is much better for flavour with the 0.65ohm coil than 416Hz. Designed to meet the needs of a wide range of vapers, the INNOKIN SENSIS POD KIT comes with special Coil+ and Coil Refresh modes, enabling you to get more flavour out of old coils. Alongside this, an accurate variable wattage mode gives you the power to dial in just the right output for your preferences. A standard 510 adapter is included with this kit so that you can use your own atomizers with the mod.Additionally, Coil + mode automatically primes the coil after each puff. This feature enhances the flavor significantly. This is accomplished by running at a reduced wattage so that the liquid can be drawn in. Coil Refresh Feature I’ve no concerns about the durability of the device, the strength of the battery or the general day to day endurance of the Innokin Kroma-Z. In regards to charging it usually took 1.5 – 2 hours to charge, which might sound like a lot, but I don’t think it’s necessarily a negative thing, especially when the battery can last so long. Innokin Sensis 510 Adapter I wish the coils we’re a little bit bigger – the reason the 0.65ohm coil couldn’t hanndle the thin high vg juice was because the coil are so small! Trying to figure out how long a coil will last is incredibly hard. The truth of the matter is many variables influence a coils life. Some people frequently vape while others not so much. Depending on the e-liquid and the wattage, you set your Sensis to affects the coil's life. If we had to compare the Sceptre S Coil in the Sensis to others, it would last on average 20-50% longer.

A pod-mod capable of the usual DTL vape, but also with precise airflow adjustment for any and every vaper. Secondly, the fill port for the liquid is at the bottom, which is inconvenient and makes the pod more prone to leaking and condensation. The Pod Mod Airflow Forgetting all the hype and hysteria and focusing on just the device for what it does, which is what i have tried to do throught the review.

The INNOKIN SENSIS POD KIT comes with two Sceptre S coils, in both 0.65Ohm and 0.25Ohm. This gives you the chance to try this range of coils, while also giving you control over the taste and flavour production of your vape. These coils can be easily changed by unscrewing the atomizer, and you can refill the whole thing with juice from a small fill port in the bottom of the device. The Sensis Kit comes with a secret power mode that enables users to further increase the flavour of their vape. Otherwise this is the same as the original with the same “ Fourth Generation Vaping Technology”– i.e. Coil + (priming the coil before each vape), Refresh (refresh the coil to help extend coil life) and F0 (alternating current with changeable frequencies). We tell you more in our article about the Sensis Chip. Depending on the frequency you choose, it often feel like the vapour is vibrating/pulsing into your mouth, it’s rather strange. Do you like the Z-coils, and do you like the Zenith or Zlide? Then this device is just perfect for you, I even enjoy vaping the Kroma Z more than the Zlide, and the Zlide has been my favorite for over a year now. Also, for smokers that are looking for a reliable, easy to use device with a long-lasting battery this is a good starter kit.

Just like on the R, the fire-button is integrated in the top of the screen making it a very comfortable fire with either thumb or index finger. Also, it can be fired with the joint of the thumb, which I like most. Thanks to Variable Wattage mode, you’ll be able to select a power output which produces an amount of power that you feel comfortable with. This means you can either experience a vape that feels closer to a cigarette or one which produces a larger amount of vapour. Thanks to the 510 adapter included, you can also pair this kit with a range of standard vape tanks and use Variable Wattage again to find the correct power output for your tank’s coils.A lot of people are often reserved about this type of fill hole but honestly a slong as the magnets hold the pod strong into the pod port then, logic dictates that will also help keep it tight. The Sensis’ full colour screen is placed on the front of the mod, ‘on’ the button (it’s not actually on the button, it’s technically underneath the button, with a clear section on the button).