PGW grants the User a personal, non-transferable, free, non-exclusive, revocable license to use the Software on User’s devices according to these terms and conditions. Finally, once the grip tape is properly applied, use a sharp hobby knife or scissors to trim any excess grip tape from around the edges of your mouse. Trimming the edges gives your mouse a clean and finished look.

As standard, the Endgame Gear XM2we is a wireless gaming mouse. Equipped with a 410mAh battery, the XM2we lasts a week of gameplay without recharging. Included within the box is the removeable Endgame Gear Flex Cord 3.0 for when you need to charge and play. Incredibly flexible, this braided cable has an angled exit from the shell, reducing drag as you manoeuvre tight corners and complex dungeons. This cable is USB 2.0 Type a to USB-C, providing a 1,000 Hz polling rate and greater compatibility when connecting to your gaming PC tower. A contributory negligence on the part of the User will be of consideration when assessing PGW’s liability. Contributory negligence on the part of the User according to this Agreement shall be assumed in the case of non-compliance with the User’s rights and obligations. The User may terminate the Agreement by deleting the Software or by declaring the termination towards PGW. The limitation period for claims made by Users, who are not private end users, shall be one year from the start of the statutory limitation period. With a little preparation and some simple steps, you can enjoy better control and performance like the pros.

There's no unnecessary RGB lighting to drain power, so the battery lasts pretty long. I didn't notice any spikes in latency or sensors cutting out when the battery was low — as I mentioned earlier, the only time I noticed any effect on the cursor was when the battery ran completely dry and the mouse turned off. As I could only gauge a rough estimation of battery life using the software, this was the main indicator that I needed to recharge — which isn't great, of course, because you don't want your mouse to die without warning in the middle of a competition. At the same time, it's kind of impressive that there's no lag in performance even when the battery is on its last legs. The Bottom Line The Endgame Gear XM2we is the first wireless mouse we’ve used in a while, and it’s made us wonder: why have we waited so long to make the switch? This sleek, lightweight mouse is understated and simple, but it’s an absolute pleasure to use. Once you have removed all the old skates from the base your mouse, give the surface a clean by using rubbing alcohol (Isopropyl). This will remove any excess adhesive that may still be present. Leave the mouse to dry, and then it's time to apply the new ones.

This Agreement regulates the provision and usage of PGW’s ENDGAME GEAR Configuration Software (hereinafter "Software") on a cost-free-basis. The User must protect any copies of the Software from being accessed by unauthorized third parties. This Agreement is effective from the date on which the Software is installed or from the date on which this Agreement is accepted and is concluded for an indefinite time period. The Agreement ends with its termination by either party. Once you have your replacement mouse skates in hand, it's now time to remove your old ones from the base of the mouse. There are a few different methods to do this, but we’ll cover the main, most reliable method (in our opinion): We've converted this review to Test Bench 1.5. This update adds a new Main Button test group, which provides button actuation data and switch information. We've also made minor changes to how we calculate the Office usage score. For more details, you can see our full changelog here.Before applying the grip tape, it is essential to clean your mouse to remove any dirt or oils that may interfere with the grip tape's adhesion. Use a soft cloth and rubbing alcohol to gently clean the surface of your mouse, taking care not to damage the coating. Make sure to remove all the dirt and oil residues, especially around the edges of your mouse. We've corrected an error in the In the Box section of this review. Previously, this section indicated this mouse had a USB-C wireless receiver. It now correctly lists that it has a USB-A wireless receiver. In accordance with the statutory provisions, PGW is solely liable for compensation of injuries to life, limb or health, for damages according to applicable product liability regulations and for damages caused by wilful intent or gross negligence on the part of PGW, whereby PGW shall not be liable for lost profits, indirect damages, consequential damages and claims third-party-claims. Speaking of gory explosions, let’s talk about the XM2we’s gaming performance. This is something of a mixed bag: flashes of excellence mingled in with frustrating shortcomings. This End User License Agreement (hereinafter “Agreement”) is an agreement between you (hereinafter “User”) and the Pro Gamersware GmbH (hereinafter „PGW“), a German limited liability company with its main offices located at Gaußstraße 1, 10589 Berlin, Germany. Unless explicitly otherwise agreed, these terms and conditions apply exclusively.

You can use the spudger or knife on its own without using the hairdryer, especially if you're unsure of how long to heat the feet up by. This may leave traces of glue on the bottom of the mouse however, which will need to be removed before attaching the new mouse feet. Making this mouse flexible to your needs, the Endgame Gear XM2we utilises a Hybrid Skate design. This allows both small and large skates to be installed on the underside of the shell. As standard, this gaming mouse comes with small skates pre-installed whilst including a set of large skates should they be your preference. Both sets are manufactured from premium PTFE plastic, ensuring the smoothest glide across any surface, as well as great durability. When operating on soft surfaces, it is recommended you equip the sensor skate too. The XM2we's design is sleek and durable, with reliable components and a new large skate design. It's the same shape as XM1 but with a lower overall weight while using a 410mAh battery. The coating is still the same matte UV coating from XM1 and XM1r, which offers a perfect grip even with sweaty hands. The XM2we charges by a supplied USB-C cable (180cm) with an angled connector. This Agreement and all disputes arising from or in connection with this Agreement are governed by the law of the Federal Republic of Germany. The provisions of the UN Sales Convention and the conflict-of-law rules are excluded. This method involves using the hairdryer to heat up the glue underneath the mouse feet. Once the glue has been heated long enough, use a spudger (a flat plastic tool with a sharp end) or a knife to scrape underneath the feet to peel them off — be careful if using a knife!Any further liability and a liability beyond the legally required liability are excluded in all cases. This Software may be subject to import and export control regulations of different countries. The User will comply with the applicable import and export control regulations of the Federal Republic of Germany, the European Union and the United States of America as well as all other relevant regulations.

reproduce, copy, distribute, sublease, resell or use the Software for any other commercial purposes, If the User is a merchant or a legal entity under German public law, or if the User does not have a general place of jurisdiction in Germany or Europe, then the exclusive place of jurisdiction for all disputes arising from this Agreement and the contractual relationship with PGW is Berlin. In other cases, the place of jurisdiction for disputes arising from or in connection with this Agreement and the contractual relationship with PGW is the User’s domicile or general place of residence. Please read this End User License Agreement carefully before you complete the installation process and before you use the ENDGAME GEAR Configuration software for the first time. By using this software (including the installation process), you declare your consent with the terms and conditions of this Agreement. If you do not agree with these terms and conditions, you are not allowed to complete the installation or use the software. End User License Agreementedit, change, modify, adapt, translate or otherwise change the Software in whole or in part, nor allow all or part of the Software to be combined with or integrated into other Software, decompile, disassemble, or reverse engineer the Software, or try to do such things,