HP J9729A Managed Ethernet Network Switch

Product Information

For use in the SFP ports of the J9263A 6600-24G Switch, the J9264A 6600-24G-4XG Switch, and the J9451A 6600-48G Switch Table 46: ( ArubaOS-CX)Compatibility for the SFP⁠+ DACs (and specifics for HPE Server cables) Product name

JL687A 32p 25G module requires configuration of "interface groups" (groups of 4 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the 8400 For J9451A: K.14.24 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 Table 45: (ArubaOS-Switch) Compatibility for the SFP⁠+ DACs (and specifics for HPE Server cables) Product name The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the For J8692A, J8693A: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D 1990-4483 and 1990-4360)

Product Reviews

For the J9308A module: K.14.34 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 For use in the JL075A SFP⁠+ ports or used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. J8992A fixed SFP ports are 1GB and do not support these SFP⁠+ copper cables. For use in an installed J9312A 10GbE 2-port SFP⁠+/2-port CX4 yl Module. JL253A, JL254A, JL255A, JL256A, JL258A, JL259A, JL260A, JL261A, JL262A, JL263A, JL264A, JL557A, JL558A, JL559A For J8705A and J8706A modules: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs).JL253A, JL254A, JL255A, JL256A, JL258A, JL263A, JL264A, JL259A, JL260A, JL261A, JL262A, JL557A, JL558A, JL559A Is it broken, do you think, or perhaps a firmware or config issue? The switch is on the latest version. For use in the JL075A SFP⁠+ ports. Also used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. For use in the SFP ports on the models listed, and in an installed J9312A 10GbE 2-port SFP⁠+/2-port CX4 yl Model

Not supported for use in the following 3800 models: J9573A, J9574A, J9575A, and J9576A. The SFP⁠+ ports do not support 100M operation. These switches only allow original SFP+ modules, unless you use the allow unsupported transceivers which voids warranty.The 8325 requires configuration of "interface groups" to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the J9772A, J9773A, J9774A, J9775A, J9776A, J9777A, J9778A, J9779A, J9780A, J9781A, J9782A, J9783A, J9853A, J9854A, J9855A, J9856A For J9310A, J9311A: K.14.50 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D) For J9537A, J9549A, J9535A, and J9637A modules: K.15.02.0004 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 For J9263A, J9264A: K.14.03 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483)

For use in the SFP ports of the 2530 Series Switches. (The J9853A, J9854A, J9855A, and J9856A models have 1G/10G SFP⁠+ ports that do not support these 100Mbps transceiver modules.) For use in the SFP ports on the models listed. Also for use in the dual-speed SFP⁠+ ports of the J9731A 2-Port 10GbE SFP⁠+ Module. The JL687A module requires configuration of "interface groups" (groups of 4 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs).ER (J9153A/D) transceivers are limited to a maximum of two transceivers per J9309A or J9538A modules when used in a 5400zl or 8200zl chassis.