When connecting the connection (1x5) cables to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected. Hold GPS Fix Timeout – is timer in which device tries to hold GPS fix for better GPS data accuracy. Default log capture time, accelerometer capture time and files directories can be changed by pressing icon at the bottom right corner. Accelerometer - after the button is pressed, the device starts to capture accelerometer values for 1 second. FMB001 FMB010 FMB002 FMB020 FMB003 FMB110 FMB120 FMB122 FMB125 FMB130 FMB202 FMB204 FMB208 FMB900 FMB920 FMB962 FMB964 FM3001 FMT100 FMC001 FMC003 FMC00A FMM001 FMM003 FMM00A FMC125 FMC130 FMM125 FMM130 FMU125 FMU126 FMU130 MTB100 FMB140

All wireless data transferring devices produce interference that may affect other devices which are placed nearby. Because our solution is developed in-house, if there’s functionality that isn’t in our system that you require, please get in touch and we will aim to accommodate your requirements. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.

You may also like…

The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard. Periodic Wakeup – if value is greater than zero, device while being in Deep Sleep or Online Deep Sleep, will wake up after defined period for beacon collection. This is mainly should be used when Bluetooth is disabled in sleep. Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.

Configurator suitable for: FMB920, FMB900, FMB910, FMB001, FMB010, FMB110, FMB120, FMB122, FMB125, FMB130, FMB202, FMB204, FMB962, FMB964, FM3001, FMT100 CONFIGURATOR VERSION

Teltonika FMB920

Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period. There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied. GPS Satellites Quantity – is value of minimum visible satellites available to device to renew GPS data after fix was acquired. Changed odometer configuration parameter available min value to 0, while on TCP configuration values is from 1 After that, the time difference is still calculated, but the difference is expected to persist for at least 5 minutes to trigger a GNSS time re-synchronization.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, TripReady to use out of the box – every device is setup, paired to your account and tested before posting

Changed setdigout command response to "DOUT is disabled from CFG" if DOUT is disabled configuration This command is used to set specific counters for vehicles. From that moment of setting the value, vehicle will continue to count from the specified value. Synchronization settings is used for choosing the device’s internal time synchronization source. Possible options are: Power-up FMB920 with DC voltage 6-30 V power supply using power cable. LED’s should start blinking, see “ FMB920 LED status”. Ignition status is used in power management and the following functionalities: Eco/Green Driving, Excessive Idling, Fuel Consumption, Over Speeding, Towing Detection and Trip.Engine RPM - if RPM from OBD II or CAN is higher than 0 - ignition is ON; if RPM from OBD II or CAN is equal to 0 - ignition is OFF; Configuration and firmware update FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration) Status info enables the user to monitor real time information of FMB920. Following fields are displayed: Device Info, GNSS Info, GSM Info, I/O Info, Maintenance and etc. User is able to export all of the information to .HTML file using icon which is at the top right corner of the Device Info area.